How to Set up a Tub: Install an Acrylic Bathtub as Well as Bathtub Surround
Click For More InformationWe've unearthed this great article relating to How to Install a Bathtub Yourself down the page on the internet and figured it made perfect sense to share it with you on this page.
Setting up a bath tub isn't precisely rocket science, however it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately difficult job. If the old tub is easily accessible, the job can move immediately; if you need to open a wall surface to eliminate the old bathtub and place the brand-new bathtub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and also set in the new one. Make certain you have certified yourself for the task and fit attempting it. Instead of working with a specialist to take control of a halfway-completed job, it is better to consider employing one before you start. Chances are you might require an expert plumber to make tube links.
This article will certainly help you set up a brand-new bathtub in your restroom if you have actually currently bought a brand-new tub and do not need to transform the plan of your previous water supply pipelines.
Your tools and also product list ought to comprise the following:
Removing Old Touches
If you need to change old taps with new ones as a part of your installation, after that the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be rather bothersome because of the restricted accessibility that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a towel ready for the remaining water that will certainly come from the pipelines. When the supply pipelines have been gotten rid of, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming throughout this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Before carrying on to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly require reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin making sure that the washing machines remain in area in between the faucet as well as the sink. Protect the faucet in position with the maker supplied backnut. When the faucet is safely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former kind must be linked to the tap ends initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bathtub
Using both wood boards under its feet, put the tub in the required position. The wooden boards are practical in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four little points.
The following goal is to ensure that the tub is leveled all round. This can be achieved by examining the spirit level and changing the feet on the bathtub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water and examine all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the bathtub as well as also inspect the overflow electrical outlet as well as the regular outlet for leakages.
Finally, take care of the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the tub needs to wait until the tub has actually been utilized at the very least once as this will resolve it into its final placement.
Preparing for the Setup
Firstly, the supporting framework provided with the bath needs to be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to see to it that if the tap includes a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its final setting.
Tiling Around the Bath tub
In the location where the bath fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack a stiff seal, triggering the water to pass through the wall between the bath and the tiling, resulting in issues with wetness and also possible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and also fittings. They are sold in tubes and cartridges, and also are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched newspaper or soft rope. Remember to always load the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in use. The sealant can crack rather very early if you do not take into consideration this movement before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly available on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic reader about A Step-by-Step Guide to Installing a Bathtub, I think sharing that excerpt was a smart idea. Remember to take the opportunity to promote this page if you liked it. Thanks a lot for your time. Please stop by our site back soon.
Details